Definition: Adjustable end is male thread stud, it consist of locknut, back-up washer, o-rings and retaining ring. DIN fittings is standard end of 24 deg cone connector and cutting ring fittings to connect steel pipe, adapters or hose assembly, adjustable stud fittings are commonly found on Elbow, Tee and Cross Fittings to allow for proper orientation of the fittings.
Methods of adjustable stud end: It will be assembled with a locknut, back-washer, sealing by O-ring or O-ring+Retaining Ring. There are four standards of sealing port as follows:
Metric thread + O-ring + Retaining O-ring (ISO 9974)
Metric thread + O-ring ISO 6149
UN/UNF thread + O-ring ISO 11926 SAE J1926 ORB
BSPP thread + O-ring + Retaining Ring (ISO 1179)
Burst and cyclic endurance(impulse) tests shall be conducted in according with ISO 19879.
 |  |
 | |
Dimensions, working pressure, performance, flatness and fit of adjustable studs end washers, O-rings, designations of stud ends, please contact us by email.
1. Elbow Fittings Adjustable 1CH9/1DH9
24 deg cone end/ Adjustable Stud End O-ring ISO 6149 Or O-ring+Retaining Ring ISO 9974
1CH4/1DH4 for 45deg elbow shape indication
|
|
PART NO. | THREAD | D1 | O RING | DIMENSIONS | MPa | ||||||
E | F | TUBE O.D. | l1 | L1 | L2 | S1 | S2 | S3 | |||
1CH9-12-10OG | M12X1.5 | M10X1 | 6 | O08.1X1.6 | 13 | 28 | 26.5 | 11 | 14 | 14 | 31.5L |
1CH9-14-12OG | M14X1.5 | M12X1.5 | 8 | O09.3X2.4 | 15.5 | 30.5 | 32 | 14 | 17 | 17 | |
1CH9-16-14OG | M16X1.5 | M14X1.5 | 10 | O11.3X2.4 | 17.5 | 32.5 | 34 | 16 | 19 | 19 | |
1CH9-18-16OG | M18X1.5 | M16X1.5 | 12 | O13.3X2.4 | 19 | 34 | 36 | 19 | 22 | 22 | |
1CH9-22-18OG | M22X1.5 | M18X1.5 | 15 | O15.3X2.4 | 22 | 37 | 39.5 | 22 | 27 | 24 | |
1CH9-26-22OG | M26X1.5 | M22X1.5 | 18 | O19.3X2.4 | 25.5 | 42 | 43.5 | 27 | 32 | 27 | |
1CH9-30-27OG | M30X2 | M27X2 | 22 | O23.5X3.0 | 29.3 | 45.8 | 50 | 30 | 36 | 32 | 16L |
1CH9-36-33OG | M36X2 | M33X2 | 28 | O29.5X3.0 | 33.3 | 49.8 | 54 | 36 | 41 | 41 | |
1DH9-14-12OG | M14X1.5 | M12X1.5 | 6 | O09.3X2.4 | 17.5 | 32.5 | 32 | 14 | 17 | 17 | 63S |
1DH9-16-14OG | M16X1.5 | M14X1.5 | 8 | O11.3X2.4 | 18.7 | 33.7 | 34 | 16 | 19 | 19 | |
1DH9-18-16OG | M18X1.5 | M16X1.5 | 10 | O13.3X2.4 | 19.5 | 36 | 36 | 19 | 22 | 22 | |
1DH9-20-18OG | M20X1.5 | M18X1.5 | 12 | O15.3X2.4 | 19.5 | 36 | 37 | 19 | 24 | 24 | |
1DH9-22-20OG | M22X1.5 | M20X1.5 | 14 | O17.3X2.4 | 23 | 41 | 40 | 22 | 27 | 27 | |
1DH9-24-22OG | M24X1.5 | M22X1.5 | 16 | O19.3X2.4 | 24 | 42 | 37.5 | 24 | 30 | 27 | |
1DH9-30-27OG | M30X2 | M27X2 | 20 | O23.5X3.0 | 28.3 | 49.8 | 50 | 30 | 36 | 32 | 40S |
1DH9-36-33OG | M36X2 | M33X2 | 25 | O29.5X3.0 | 32.8 | 56.8 | 54 | 36 | 46 | 41 | |
1DH9-42OG | M42X2 | M42X2 | 30 | O38.5X3.0 | 36.2 | 62.7 | 57.2 | 41 | 50 | 50 | |
Note: In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix "RN" after our part no. for example 1DH9-20-18OG/RN. | |||||||||||
2. Elbow Fittings Adjustable 1CO9/1DO9
24 deg cone end/ Adjustable Stud End O-ring ISO 11926
1CO4/1DO4 for 45 deg elbow shape indication
|
|
PART NO. | THREAD | TUBE O.D. | DIMENSIONS | MPa | ||||||
E | F | D1 | l1 | L1 | L2 | S1 | S2 | S3 | ||
1CO9-12-04OG | M12X1.5 | 7/16"X20 | 6 | 13 | 28 | 27.2 | 11 | 14 | 17 | 31.5L |
1CO9-14-06OG | M14X1.5 | 9/16"X18 | 8 | 15.5 | 30.5 | 31.8 | 14 | 17 | 19 | |
1CO9-16-06OG | M16X1.5 | 9/16"X18 | 10 | 17.5 | 32.5 | 33.3 | 16 | 19 | 19 | |
1CO9-18-08OG | M18X1.5 | 3/4"X16 | 12 | 19 | 34 | 37.5 | 19 | 22 | 24 | |
1CO9-22-10OG | M22X1.5 | 7/8"X14 | 15 | 22 | 37 | 44 | 22 | 27 | 27 | |
1CO9-22-08OG | M22X1.5 | 3/4"X16 | 15 | 22 | 37 | 39.5 | 22 | 27 | 24 | |
1CO9-26-12OG | M26X1.5 | 1.1/16"X12 | 18 | 25.5 | 42 | 51 | 27 | 32 | 32 | |
1CO9-30-12OG | M30X2 | 1.1/16"X12 | 22 | 29.3 | 45.8 | 53.5 | 30 | 36 | 32 | 16L |
1CO9-36-12OG | M36X2 | 1.1/16"X12 | 28 | 33.5 | 47.8 | 57.5 | 36 | 41 | 41 | |
1CO9-36-16OG | M36X2 | 1.5/16"X12 | 28 | 33.3 | 49.8 | 57.5 | 36 | 41 | 41 | |
1CO9-45-20OG | M45X2 | 1.5/8"X12 | 35 | 39.2 | 60.7 | 63 | 48 | 50 | 50 | |
1CO9-52-24OG | M52X2 | 1.7/8"X12 | 42 | 44.8 | 67.8 | 70.5 | 55 | 60 | 55 | |
1DO9-14-04OG | M14X1.5 | 7/16"X20 | 6 | 17.5 | 32.5 | 30 | 14 | 17 | 17 | 63S |
1DO9-16-06OG | M16X1.5 | 9/16"X18 | 8 | 18.7 | 33.7 | 33.3 | 16 | 19 | 19 | |
1DO9-18-06OG | M18X1.5 | 9/16"X18 | 10 | 19.5 | 36 | 33.5 | 19 | 22 | 19 | |
1DO9-18-08OG | M18X1.5 | 3/4"X16 | 10 | 19.5 | 36 | 37.5 | 19 | 22 | 24 | |
1DO9-20-08OG | M20X1.5 | 3/4"X16 | 12 | 19.5 | 36 | 37.5 | 19 | 24 | 24 | |
1DO9-22-10OG | M22X1.5 | 7/8"X14 | 14 | 23 | 41 | 44 | 22 | 27 | 27 | |
1DO9-24-10OG | M24X1.5 | 7/8"X14 | 16 | 24 | 42.5 | 46.5 | 24 | 30 | 27 | 40S |
1DO9-30-12OG | M30X2 | 1.1/16"X12 | 20 | 28.3 | 49.8 | 53.5 | 30 | 36 | 32 | |
1DO9-36-16OG | M36X2 | 1.5/16"X12 | 25 | 32.8 | 56.8 | 57.5 | 36 | 46 | 41 | |
1DO9-42-20OG | M42X2 | 1.5/8"X12 | 30 | 36.2 | 62.7 | 59.5 | 41 | 50 | 50 | |
1DO9-52-24OG | M52X2 | 1.7/8"X12 | 38 | 45.8 | 76.8 | 70.5 | 55 | 60 | 55 | 31.5S |
Note: In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix "RN" after our part no. for example 1CO9-30-120G/RN. | ||||||||||
3. Elbow Fittings Adjustable 1CG9/1DG9
24 deg cone end/ Adjustable Stud End O-ring+Retaining Ring ISO 1179
1CG4/1DG4 for 45deg elbow shape indication
|
|
PART NO. | THREAD | TUBE O.D. | DIMENSIONS | MPa | ||||||
E | F | D1 | l1 | L1 | L2 | S1 | S2 | S3 | ||
1CG9-12-02OG | M12X1.5 | G1/8"X28 | 6 | 13 | 28 | 26.2 | 11 | 14 | 14 | 31.5L |
1CG9-14-04OG | M14X1.5 | G1/4"X19 | 8 | 15.5 | 30.5 | 31.3 | 14 | 17 | 19 | |
1CG9-16-04OG | M16X1.5 | G1/4"X19 | 10 | 17.5 | 32.5 | 32.5 | 16 | 19 | 19 | |
1CG9-16-06OG | M16X1.5 | G3/8"X19 | 10 | 17.5 | 32.5 | 35.8 | 16 | 19 | 22 | |
1CG9-18-06OG | M18X1.5 | G3/8"X19 | 12 | 19 | 34 | 36.8 | 19 | 22 | 22 | |
1CG9-22-08OG | M22X1.5 | G1/2"X14 | 15 | 22 | 37 | 43.2 | 22 | 27 | 27 | |
1CG9-26-08OG | M26X1.5 | G1/2"X14 | 18 | 25.5 | 42 | 46 | 27 | 32 | 27 | |
1CG9-26-12OG | M26X1.5 | G3/4"X14 | 18 | 25.5 | 42 | 49.3 | 27 | 32 | 32 | |
1CG9-30-12OG | M30X2 | G3/4"X14 | 22 | 29.3 | 45.8 | 52 | 30 | 36 | 32 | 16L |
1CG9-30-16OG | M30X2 | G1"X11 | 22 | 31.5 | 48 | 53 | 33 | 36 | 41 | |
1CG9-36-16OG | M36X2 | G1"X11 | 28 | 33 | 49.8 | 56 | 36 | 41 | 41 | |
1CG9-36-20OG | M36X2 | G1.1/4"X11 | 28 | 36 | 52.8 | 59 | 41 | 41 | 50 | |
1CG9-45-20OG | M45X2 | G1.1/4"X11 | 35 | 39.2 | 60.7 | 63 | 48 | 50 | 50 | |
1CG9-52-24OG | M52X2 | G1.1/2"X11 | 42 | 44.8 | 67.8 | 68.5 | 55 | 60 | 55 | |
1DG9-14-04OG | M14X1.5 | G1/4"X19 | 6 | 17.5 | 32.5 | 31.3 | 14 | 17 | 19 | 63S |
1DG9-16-04OG | M16X1.5 | G1/4"X19 | 8 | 18.7 | 33.7 | 32.5 | 16 | 19 | 19 | |
1DG9-16-06OG | M16X1.5 | G3/8"X19 | 8 | 18.7 | 33.7 | 35.8 | 16 | 19 | 22 | |
1DG9-18-06OG | M18X1.5 | G3/8"X19 | 10 | 19.5 | 36 | 36.8 | 19 | 22 | 22 | |
1DG9-20-06OG | M20X1.5 | G3/8"X19 | 12 | 19.5 | 36 | 36.8 | 19 | 24 | 22 | |
1DG9-22-08OG | M22X1.5 | G1/2"X14 | 14 | 23 | 41 | 43.2 | 22 | 27 | 27 | |
1DG9-24-08OG | M24X1.5 | G1/2"X14 | 16 | 24 | 42.5 | 43 | 24 | 30 | 27 | 40S |
1DG9-30-12OG | M30X2 | G3/4"X14 | 20 | 28 | 49.5 | 52 | 30 | 36 | 32 | |
1DG9-36-16OG | M36X2 | G1"X11 | 25 | 32.8 | 56.8 | 56 | 36 | 46 | 41 | |
1DG9-42-20OG | M42X2 | G1.1/4"X11 | 30 | 36.2 | 62.7 | 58 | 41 | 50 | 50 | |
1DG9-52-24OG | M52X2 | G1.1/2"X11 | 38 | 45.8 | 76.8 | 68.5 | 55 | 60 | 55 | 31.5S |
Note: In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix "RN" after our part no. for example 1CG9-30-12OG/RN. | ||||||||||
4. Run Tee Fittings Adjustable ACCH/ADDH
24 deg cone/ 24 deg cone/ Adjustable Stud End O-ring ISO 6149 Or O-ring+Retaining Ring ISO 9974
|
|
PART NO. | THREAD | D1,D2 | O RING | DIMENSIONS | MPa | ||||||
E,F | G | TUBE O.D. | l1,l2 | L1,L2 | L3 | S1 | S2,S3 | S4 | |||
ACCH-12-12-10OG | M12X1.5 | M10X1 | 6 | O08.1X1.6 | 13 | 28 | 26.5 | 11 | 14 | 14 | 31.5L |
ACCH-14-14-12OG | M14X1.5 | M12X1.5 | 8 | O09.3X2.4 | 15.5 | 30.5 | 32 | 14 | 17 | 17 | |
ACCH-16-16-14OG | M16X1.5 | M14X1.5 | 10 | O11.3X2.4 | 17.5 | 32.5 | 34 | 16 | 19 | 19 | |
ACCH-18-18-16OG | M18X1.5 | M16X1.5 | 12 | O13.3X2.4 | 19 | 34 | 36 | 19 | 22 | 22 | |
ACCH-22-22-18OG | M22X1.5 | M18X1.5 | 15 | O15.3X2.4 | 22 | 37 | 39.5 | 22 | 27 | 24 | |
ACCH-26-26-22OG | M26X1.5 | M22X1.5 | 18 | O19.3X2.4 | 25.5 | 42 | 43.5 | 27 | 32 | 27 | |
ACCH-30-30-27OG | M30X2 | M27X2 | 22 | O23.5X3.0 | 29.3 | 45.8 | 50 | 30 | 36 | 32 | 16L |
ACCH-36-36-33OG | M36X2 | M33X2 | 28 | O29.2X3.0 | 33.3 | 49.8 | 54 | 36 | 41 | 41 | |
ADDH-14-14-12OG | M14X1.5 | M12X1.5 | 6 | O09.3X2.4 | 17.5 | 32.5 | 32 | 14 | 17 | 17 | 63S |
ADDH-16-16-14OG | M16X1.5 | M14X1.5 | 8 | O11.3X2.4 | 18.7 | 33.7 | 34 | 16 | 19 | 19 | |
ADDH-18-18-16OG | M18X1.5 | M16X1.5 | 10 | O13.3X2.4 | 19.5 | 36 | 36 | 19 | 22 | 22 | |
ADDH-20-20-18OG | M20X1.5 | M18X1.5 | 12 | O15.3X2.4 | 19.5 | 36 | 37 | 19 | 24 | 24 | |
ADDH-24-24-22OG | M24X1.5 | M22X1.5 | 16 | O19.3X2.4 | 24 | 42 | 37.5 | 24 | 30 | 27 | |
ADDH-30-30-27OG | M30X2 | M27X2 | 20 | O23.5X3.0 | 28.3 | 49.8 | 50 | 30 | 36 | 32 | 40S |
ADDH-36-36-33OG | M36X2 | M33X2 | 25 | O29.2X3.0 | 32.8 | 56.8 | 54 | 36 | 46 | 41 | |
ADDH-42-42-42OG | M42X2 | M42X2 | 30 | O38.5X3.0 | 36.2 | 62.7 | 57.2 | 41 | 50 | 50 | |
Note: 1. In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix "RN" after our part no. for example ACCH-30-30-27OG/RN. | |||||||||||
5. Run Tee Fittings Adjustable ACCO/ADDO
24 deg cone/ 24 deg cone/ Adjustable Stud End O-ring ISO 11926
|
|
PART NO. | THREAD | TUBE O.D. | DIMENSIONS | MPa | ||||||
E,F | G | D1,D2 | l1,l2 | L1,L2 | L3 | S1 | S2,S3 | S4 | ||
ACCO-12-12-04OG | M12X1.5 | 7/16"X20 | 6 | 13 | 28 | 27.2 | 11 | 14 | 17 | 31.5L |
ACCO-14-14-06OG | M14X1.5 | 9/16"X18 | 8 | 15.5 | 30.5 | 31.8 | 14 | 17 | 19 | |
ACCO-16-16-06OG | M16X1.5 | 9/16"X18 | 10 | 17.5 | 32.5 | 33.3 | 16 | 19 | 19 | |
ACCO-18-18-08OG | M18X1.5 | 3/4"X16 | 12 | 19 | 34 | 37.5 | 19 | 22 | 24 | |
ACCO-22-22-10OG | M22X1.5 | 7/8"X14 | 15 | 22 | 37 | 44 | 22 | 27 | 27 | |
ACCO-26-26-12OG | M26X1.5 | 1.1/16"X12 | 18 | 25.5 | 42 | 51 | 27 | 32 | 32 | |
ACCO-30-30-12OG | M30X2 | 1.1/16"X12 | 22 | 29.3 | 45.8 | 53.5 | 30 | 36 | 32 | 16L |
ACCO-36-36-16OG | M36X2 | 1.5/16"X12 | 28 | 33.3 | 49.8 | 57.5 | 36 | 41 | 41 | |
ACCO-45-45-20OG | M45X2 | 1.5/8"X12 | 35 | 39.2 | 60.7 | 63 | 48 | 50 | 50 | |
ADDO-14-14-04OG | M14X1.5 | 7/16"X20 | 6 | 17.5 | 32.5 | 30 | 14 | 17 | 17 | 63S |
ADDO-16-16-06OG | M16X1.5 | 9/16"X18 | 8 | 18.7 | 33.7 | 33.3 | 16 | 19 | 19 | |
ADDO-18-18-06OG | M18X1.5 | 9/16"X18 | 10 | 19.5 | 36 | 33.5 | 19 | 22 | 19 | |
ADDO-20-20-08OG | M20X1.5 | 3/4"X16 | 12 | 19.5 | 36 | 37.5 | 19 | 24 | 24 | |
ADDO-22-22-10OG | M22X1.5 | 7/8"X14 | 14 | 23 | 41 | 44 | 22 | 27 | 27 | |
ADDO-24-24-10OG | M24X1.5 | 7/8"X14 | 16 | 24 | 42.5 | 46.5 | 24 | 30 | 27 | 40S |
ADDO-30-30-12OG | M30X2 | 1.1/16"X12 | 20 | 28.3 | 49.8 | 53.5 | 30 | 36 | 32 | |
ADDO-36-36-16OG | M36X2 | 1.5/16"X12 | 25 | 32.8 | 56.8 | 57.5 | 36 | 46 | 41 | |
ADDO-42-42-20OG | M42X2 | 1.5/8"X12 | 30 | 36.2 | 62.7 | 59.5 | 41 | 50 | 50 | |
Note: In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix"RN" after our part no. for example ACCO-30-30-12OG/RN. | ||||||||||
6. Run Tee Fittings Adjustable ACCG/ADDG
24 deg cone/ 24 deg cone/ Adjustable Stud End O-ring+Retaining Ring ISO 1179
|
|
PART NO. | THREAD | TUBE O.D. | DIMENSIONS | MPa | ||||||
E,F | G | D1,D2 | l1,l2 | L1,L2 | L3 | S1 | S2,S3 | S4 | ||
ACCG-12-12-02OG | M12X1.5 | G1/8"X28 | 6 | 13 | 28 | 26.2 | 11 | 14 | 14 | 31.5 |
ACCG-14-14-04OG | M14X1.5 | G1/4"X19 | 8 | 15.5 | 30.5 | 31.3 | 14 | 17 | 19 | |
ACCG-16-16-04OG | M16X1.5 | G1/4"X19 | 10 | 17.5 | 32.5 | 32.5 | 16 | 19 | 19 | |
ACCG-18-18-06OG | M18X1.5 | G3/8"X19 | 12 | 19 | 34 | 36.8 | 19 | 22 | 22 | |
ACCG-22-22-08OG | M22X1.5 | G1/2"X14 | 15 | 22 | 37 | 43.2 | 22 | 27 | 27 | |
ACCG-26-26-08OG | M26X1.5 | G1/2"X14 | 18 | 25.5 | 42 | 46.5 | 27 | 32 | 27 | |
ACCG-30-30-12OG | M30X2 | G3/4"X14 | 22 | 29.3 | 45.8 | 52 | 30 | 36 | 32 | 16 |
ACCG-36-36-16OG | M36X2 | G1"X11 | 28 | 33.3 | 49.8 | 56 | 36 | 41 | 41 | |
ACCG-45-45-20OG | M45X2 | G1.1/4"X11 | 35 | 39.2 | 60.7 | 63 | 48 | 50 | 50 | |
ADDG-14-14-04OG | M14X1.5 | G1/4"X19 | 6 | 17.5 | 32.5 | 31.3 | 14 | 17 | 19 | 63S |
ADDG-16-16-04OG | M16X1.5 | G1/4"X19 | 8 | 18.7 | 33.7 | 32.5 | 16 | 19 | 19 | |
ADDG-18-18-06OG | M18X1.5 | G3/8"X19 | 10 | 19.5 | 36 | 36.8 | 19 | 22 | 22 | |
ADDG-20-20-06OG | M20X1.5 | G3/8"X19 | 12 | 19.5 | 36 | 36.8 | 19 | 24 | 22 | |
ADDG-22-22-08OG | M22X1.5 | G1/2"X14 | 14 | 23 | 41 | 43.2 | 22 | 27 | 27 | |
ADDG-24-24-08OG | M24X1.5 | G1/2"X14 | 16 | 24 | 42.5 | 44 | 24 | 30 | 27 | 40S |
ADDG-30-30-12OG | M30X2 | G3/4"X14 | 20 | 28.3 | 49.8 | 52 | 30 | 36 | 32 | |
ADDG-36-36-16OG | M36X2 | G1"X11 | 25 | 32.8 | 56.8 | 56 | 36 | 46 | 41 | |
ADDG-42-42-20OG | M42X2 | G1.1/4"X11 | 30 | 36.2 | 62.7 | 58 | 41 | 50 | 50 | |
Note: In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix "RN" after our Part No. for example ACCG-18-18-06OG/RN. | ||||||||||
7. Branch Tee Fittings Adjustable ACHC/ADHD
24 deg cone/ Adjustable Stud End O-ring ISO 6149 or O-ring+Retaining Ring ISO 9974/24 deg cone
|
|
PART NO. | THREAD | D1,D2 | O-Ring | DIMENSIONS | MPa | ||||||
E,G | F | TUBE O.D. | l1,l2 | L1,L2 | L3 | S1 | S2,S4 | S3 | |||
ACHC-12-10-12OG | M12X1.5 | M10X1 | 6 | O08.1X1.6 | 13 | 28 | 26.5 | 11 | 14 | 14 | 31.5L |
ACHC-14-12-14OG | M14X1.5 | M12X1.5 | 8 | O09.3X2.4 | 15.5 | 30.5 | 32 | 14 | 17 | 17 | |
ACHC-16-14-16OG | M16X1.5 | M14X1.5 | 10 | O11.3X2.4 | 17.5 | 32.5 | 34 | 16 | 19 | 19 | |
ACHC-18-16-18OG | M18X1.5 | M16X1.5 | 12 | O13.3X2.4 | 19 | 34 | 36 | 19 | 22 | 22 | |
ACHC-22-18-22OG | M22X1.5 | M18X1.5 | 15 | O15.3X2.4 | 22 | 37 | 39.5 | 22 | 27 | 24 | |
ACHC-26-22-26OG | M26X1.5 | M22X1.5 | 18 | O19.3X2.4 | 25.5 | 42 | 43.5 | 27 | 32 | 27 | |
ACHC-30-27-30OG | M30X2 | M27X2 | 22 | O23.5X3.0 | 29.3 | 45.8 | 50 | 30 | 36 | 32 | 16 |
ACHC-36-33-36OG | M36X2 | M33X2 | 28 | O29.2X3.0 | 33.3 | 49.8 | 54 | 36 | 41 | 41 | |
ADHD-14-12-14OG | M14X1.5 | M12X1.5 | 6 | O09.3X2.4 | 17.5 | 32.5 | 32 | 14 | 17 | 17 | 63S |
ADHD-16-14-16OG | M16X1.5 | M14X1.5 | 8 | O11.3X2.4 | 18.7 | 33.7 | 34 | 16 | 19 | 19 | |
ADHD-18-16-18OG | M18X1.5 | M16X1.5 | 10 | O13.3X2.4 | 19.5 | 36 | 36 | 19 | 22 | 22 | |
ADHD-20-18-20OG | M20X1.5 | M18X1.5 | 12 | O15.3X2.4 | 19.5 | 36 | 37 | 19 | 24 | 24 | |
ADHD-24-22-24OG | M24X1.5 | M22X1.5 | 16 | O19.3X2.4 | 24 | 42 | 37.5 | 24 | 30 | 27 | |
ADHD-30-27-30OG | M30X2 | M27X2 | 20 | O23.5X3.0 | 28.3 | 49.8 | 50 | 30 | 36 | 32 | 40S |
ADHD-36-33-36OG | M36X2 | M33X2 | 25 | O29.2X3.0 | 32.8 | 56.8 | 54 | 36 | 46 | 41 | |
ADHD-42-42-42OG | M42X2 | M42X2 | 30 | O38.5X3.0 | 36.2 | 62.7 | 57.2 | 41 | 50 | 50 | |
Note: 1. In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix "RN" after our part no. for example ACHC-30-27-30OG/RN. | |||||||||||
8. Branch Tee Fittings Adjustable ACOC/ADOD
24 deg cone/ Adjustable Stud End O-ring ISO 11926/ 24 deg cone
|
|
PART NO. | THREAD | TUBE O.D. | DIMENSIONS | MPa | ||||||
E,G | F | D1,D2 | l1,l2 | L1,L2 | L3 | S1 | S2,S4 | S3 | ||
ACOC-12-04-12OG | M12X1.5 | 7/16"X20 | 6 | 13 | 28 | 27.2 | 11 | 14 | 17 | 31.5L |
ACOC-14-06-14OG | M14X1.5 | 9/16"X18 | 8 | 15.5 | 30.5 | 31.8 | 14 | 17 | 19 | |
ACOC-16-06-16OG | M16X1.5 | 9/16"X18 | 10 | 17.5 | 32.5 | 33.3 | 16 | 19 | 19 | |
ACOC-18-08-18OG | M18X1.5 | 3/4"X16 | 12 | 19 | 34 | 37.5 | 19 | 22 | 24 | |
ACOC-22-10-22OG | M22X1.5 | 7/8"X14 | 15 | 22 | 37 | 44 | 22 | 27 | 27 | |
ACOC-26-12-26OG | M26X1.5 | 1.1/16"X12 | 18 | 25.5 | 42 | 51 | 27 | 32 | 32 | |
ACOC-30-12-30OG | M30X2 | 1.1/16"X12 | 22 | 29.3 | 45.8 | 53.5 | 30 | 36 | 32 | 16L |
ACOC-36-16-36OG | M36X2 | 1.5/16"X12 | 28 | 33.3 | 49.8 | 57.5 | 36 | 41 | 41 | |
ACOC-45-20-45OG | M45X2 | 1.5/8"X12 | 35 | 39.2 | 60.7 | 63 | 48 | 50 | 50 | |
ADOD-14-04-14OG | M14X1.5 | 7/16"X20 | 6 | 17.5 | 32.5 | 30 | 14 | 17 | 17 | 63S |
ADOD-16-06-16OG | M16X1.5 | 9/16"X18 | 8 | 18.7 | 33.7 | 33.3 | 16 | 19 | 19 | |
ADOD-18-06-18OG | M18X1.5 | 9/16"X18 | 10 | 19.5 | 36 | 33.5 | 19 | 22 | 19 | |
ADOD-20-08-20OG | M20X1.5 | 3/4"X16 | 12 | 19.5 | 36 | 37.5 | 19 | 24 | 24 | |
ADOD-22-10-22OG | M22X1.5 | 7/8"X14 | 14 | 23 | 41 | 44 | 22 | 27 | 27 | |
ADOD-24-10-24OG | M24X1.5 | 7/8"X14 | 16 | 24 | 42.5 | 46.5 | 24 | 30 | 27 | 40S |
ADOD-30-12-30OG | M30X2 | 1.1/16"X12 | 20 | 28.3 | 49.8 | 53.5 | 30 | 36 | 32 | |
ADOD-36-16-36OG | M36X2 | 1.5/16"X12 | 25 | 32.8 | 56.8 | 57.5 | 36 | 46 | 41 | |
ADOD-42-20-42OG | M42X2 | 1.5/8"X12 | 30 | 36.2 | 62.7 | 59.5 | 41 | 50 | 50 | |
Note: In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix "RN" after our part no. for example ACOC-30-12-30OG/RN. | ||||||||||
9. Branch Tee Fittings Adjustable ACGC/ADGD
24 deg cone/ Adjustable Stud End O-ring+Retaining Ring ISO 1179/ 24 deg cone
|
|
PART NO. | THREAD | TUBE O.D. | DIMENSIONS | MPa | ||||||
E,G | F | D1,D2 | l1,l2 | L1,L2 | L3 | S1 | S2,S4 | S3 | ||
ACGC-12-02-12OG | M12X1.5 | G1/8"X28 | 6 | 13 | 28 | 26.2 | 11 | 14 | 14 | 31.5L |
ACGC-14-04-14OG | M14X1.5 | G1/4"X19 | 8 | 15.5 | 30.5 | 31.3 | 14 | 17 | 19 | |
ACGC-16-04-16OG | M16X1.5 | G1/4"X19 | 10 | 17.5 | 32.5 | 32.5 | 16 | 19 | 19 | |
ACGC-18-06-18OG | M18X1.5 | G3/8"X19 | 12 | 19 | 34 | 36.8 | 19 | 22 | 22 | |
ACGC-22-08-22OG | M22X1.5 | G1/2"X14 | 15 | 22 | 37 | 43.2 | 22 | 27 | 27 | |
ACGC-26-08-26OG | M26X1.5 | G1/2"X14 | 18 | 25.5 | 42 | 46.5 | 27 | 32 | 27 | |
ACGC-30-12-30OG | M30X2 | G3/4"X14 | 22 | 29.3 | 45.8 | 52 | 30 | 36 | 32 | 16L |
ACGC-36-16-36OG | M36X2 | G1"X11 | 28 | 33.3 | 49.8 | 56 | 36 | 41 | 41 | |
ACGC-45-20-45OG | M45X2 | G1.1/4"X11 | 35 | 39.2 | 60.7 | 63 | 48 | 50 | 50 | |
ADGD-14-04-14OG | M14X1.5 | G1/4"X19 | 6 | 17.5 | 32.5 | 31.3 | 14 | 17 | 19 | 63S |
ADGD-16-04-16OG | M16X1.5 | G1/4"X19 | 8 | 18.7 | 33.7 | 32.5 | 16 | 19 | 19 | |
ADGD-18-06-18OG | M18X1.5 | G3/8"X19 | 10 | 19.5 | 36 | 36.8 | 19 | 22 | 22 | |
ADGD-20-06-20OG | M20X1.5 | G3/8"X19 | 12 | 19.5 | 36 | 36.8 | 19 | 24 | 22 | |
ADGD-22-08-22OG | M22X1.5 | G1/2"X14 | 14 | 23 | 41 | 43.2 | 22 | 27 | 27 | |
ADGD-24-08-24OG | M24X1.5 | G1/2"X14 | 16 | 24 | 42.5 | 44 | 24 | 30 | 27 | 40S |
ADGD-30-12-30OG | M30X2 | G3/4"X14 | 20 | 28.3 | 49.8 | 52 | 30 | 36 | 32 | |
ADGD-36-16-36OG | M36X2 | G1"X11 | 25 | 32.8 | 56.8 | 56 | 36 | 46 | 41 | |
ADGD-42-20-42OG | M42X2 | G1.1/4"X11 | 30 | 36.2 | 62.7 | 58 | 41 | 50 | 50 | |
Note: In case if you are interested to order the adapter in complete set with cutting ring and nut, it is necessary to insert suffix "RN" after our part no. for example ACGC-18-06-18OG/RN. | ||||||||||
Hot Tags: DIN fittings adjustable, China, manufacturers, suppliers, custom, brass, swagelok, Parker, Stauff, Brennan, stainless steel
